Setting up A Bathtub
Setting up A Bathtub
Blog Article
The publisher is making several good points on the subject of Installing A Bathtub in general in this article down the page.
Installing a tub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old tub is easily easily accessible, the task can relocate easily; if you have to open a wall to remove the old tub and position the new tub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly need a helper to move out the old tub and set in the brand-new one. Make sure you have certified on your own for the task and are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This write-up will certainly aid you set up a brand-new tub in your restroom if you have already acquired a brand-new tub and don't need to change the arrangement of your previous water pipelines.
Your devices as well as material checklist need to consist of the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the limited accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in place with the maker provided backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet adapters. The former type must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed placement. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bathtub until the spirit level checks out level.
To install taps, fit the bottom of the outermost versatile faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the supply of water as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise inspect the overflow outlet and the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has been made use of at the very least once as this will resolve it right into its last setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, causing complications with wetness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the movement experienced when the tub remains in usage. The sealant can crack relatively very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very taken with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you liked the new blog entry. For those who enjoyed our blog entry please remember to pass it around. We cherish reading our article about How to Install a Bathtub.
Click For More Information
Report this page